Ingersol Backhoe

A Great Pay Back is the Payoff with Ingersoll.

Ingersoll engineered this unit to handle heavy loads and to work long hours.The entire unit has been designed for easy operation. Power steering - standard. Forward and reverse - single lever shifting. Speed control - right mounted foot pedal. Swing and boom - single lever control. Crowd and bucket - single lever again. Stabilizer pads - quick setting so you're up and runnung fast. Ingersoll is an operator friendly piece of iron so you can do more in less time. The 6018 LBH can be towed on a traiker behind a pick up truck. Plus its lower weight doesn't tear-up turf on the job site.

It's built tough for years of dependable service. Welded steel channel frame and cast iron rear axle - engineered for heavy loads and long hours on the job. The loader is designed as an integral part of the tractor and frame with eavy lift arms and reinforced bucket for maximum strength. Tandem hydraulic pump mounted directly to the engine crankshaft with a flexible coupling operates the loader, backhoe, power steering and traction drive. Built-in oil cooler and reservoir ensire top operating efficiency.

A	Maximum dump angle	60o
B	Reach at 60o dump angle	12.50" (317 mm)
C	Reach at 45o dump angle	17.50" (444 mm)
D	Clearance at 59o dump angle	51.00" (1,295 mm)
E	Clearance at 45o dump angle	53.00" (1,346 mm)
F	Height to bucket hinge pin	72.00" (1,829 mm)
G	Fully Raised operating height	88.00" (2,235 mm)
H	Bucket roll back	18o
J	Digging depth, bucket flat	3.00" (76 mm)
K	Backhoe Digging depth	92.00" (2,337 mm)
L	Backhoe Undercut	30.00" (762 mm)
M	Digging radius from pivot center Swing arc from pivot center	112.00" (2,845 mm) 180o
N	Loading height - bucket at 60o	68.00" (1,727 mm)
O	Loading reach - bucket at 60o	41.00" (1,041 mm)
P	Maximum transport height	72.00" (1,828 mm)
Q	Transport overhang	39.50" (1,003 mm)
R	Wheelbase	48.00" (1,219 mm)
S	Length - bucket to rear tire Overall trailering length LBH Overall trailering width LBH	98.50" (2,501 mm) 156.00" (3,962 mm) 60.00" (1,524 mm)
T	Overall trailering length L Overall trailering width L Bucket at 180o	107.00" (2,717 mm) 49.00" (1,244 mm) 130.00" (3,302 mm)

Engine
	Make	Onan, 2 cylinder 4 cycle air-cooled with full pressure lubrication
	Model	PS18G
	Horsepower	18 at 3600 RPM
	Bore & Stroke	3.25" x 2.88" (82.5mm x 73mm)
	Displacement	47.7 cu. in. (782cc)
	Block	Aluminum with cast iron cylinder liners
	Air Cleaner	Dry Type (Replaceable)
	Oil Filter	Can Type (Replaceable)
	Fuel	Gasoline, regular or unleaded
	Electronics	Solenoid Shift Bendix drive starter 20 amp. flywheel laternator
	Battery	300 CCA
	Instruments	Electric hour meter, ammeter
Power Train
	Transaxle	Dual Range, cast iron, automative differential
	Front axle	Steel with tapered roller bearings spindles, 1.25 in (32mm) static capacity, 3000 lbs (1362kg)
	Steering	Hydraulic Power
	Brakes	Band and drum
	Parking Brakes	Hand set
Attachments
	Optional eqt	Pallet Forks, R.O.P.S and hydraulic tools
Fluid Capacities
	Hydraulics	Loader 3.225 gal. (12.3L) Backhoe 5.0 gal. (18.9L)
	Engine Oil	1.8 qt. (1.7L)
	Transaxle	3 qt. (2.8L)
	Fuel Tank	6.4 gal, (24.2L)
Hydraulic Systems
	Motor	Low speed, high torque high efficiency gerotor type motor
	Oil Type	SAE 20W-40 motor oil recommended
	Oil Cooler	Air cooled radiator
	Oil Reservoir	2.25 gal. (8.5L)
	Oil Filter	Can type (replaceable)
	Pump	Double gear type, Port #1:4.7 GPM (17.8 LPM), Port #2: 8.7 GPM (32.9 LPM), at 3600 RPM and 2500 PSI (17,225 KPa)
	Control Valve	Mono-cast, 2 spool series valve
	Dynamic	Pilot operated
	Braking Valve	spool valve
Hydraulic Pressure Relief Settings
	Traction Control	2500psi (17,225 KPa)
	PTO Valve	2100psi (14,469 KPa)
	Power Steering	1800psi (12,402 KPa)
	Loader Control	1800psi (12,402 KPa)
Tires
	Loader Rear	27 x 10.5-15 4 ply high flotation pressure, 20psi (138 KPa)
	Backhoe Rear	29 x 12.50-15 4 ply high flotation pressure 20psi (138 KPa)
	Front (both)	18 x 8.50-8 4 ply flotationi pressure 22psi (152 KPa)
Loader
	Bucket Capacity	4.7 ct. ft. (.15m3) struck
	Load Lift Capacity	750 lbs. (340.2 kg) at maximum operating height
	Breakout Capacity	1,409 lbs. (639 kg) per SAE J 732
	Bucket Width	48 on. (1.21 m)
	Power	Hydraulic, supplied by tractor system
	Control Valve	Mono-cast 2 spool, single lever operation for lift and dump position. Positive hold and float position
Loader Travel Speeds
	Low Range	0-3.0 mph (4.8 km/h) forward and reverse
	High Range	0-5.4 mph (8.6 km/h) forward and reverse
Loader Cylnders
	Loader Lift (2)	2 in. (51 mm) bore 18.1 in (.46 m) stroke 1 in. (25.4 mm) dia. rod, Double acting
	Bucket (1)	2.5 in. (63.5 mm) bore 13 in. (33 m) stroke 1.25 in. (31.7 mm) dia rod, Double acting
Backhoe
	Bucket Capacity, Struck
	9 inch	0.50 cu. ft. (.014 m3)
	13 inch	0.75 cu. ft.(.012 m3)
	16 inch	0.94 cu. ft. (.026 m3)
	19 inch	1.13 cu. ft. (.031 m3)
	24 inch	1.44 cu. ft. (0.40 m3)
	36 inch	2.19 cu. ft. (0.61 m3)
	Bucket Capacity, Heaped
	9 inch	0.63 cu. ft. (0.17 m3)
	13 inch	1.00 cu. ft. (0.28 m3)
	16 inch	1.25 cu. ft. (.035 m3)
	19 inch	1.50 cu. ft. (.042 m3)
	24 inch	2.00 cu. ft. (.056 m3)
	36 inch	3.01 cu. ft. (.085 m3)
Backhoe travel speeds
	Low Range	0-3.2 mph (5.1 km/h) forward and reverse
	High Range	0-5.7 mph (9.1 km/h) forward and reverse
Backhoe Cylinders
	Boom	2.0" (51 mm) Bore
	Dipperstick	2.0" (51 mm) Bore
	Bucket	2.0" (51 mm) Bore
	Stabilizer	2.0" (51 mm) Bore
	Swing	2.0" (51 mm) Bore